Search results for “74FCT162”

The 74FCT16244TPACTG4 from Texas Instruments is a non-inverting buffer Integrated Circuit with 4 elements, 4 bits per element and 3-state outputs, rated 5.5 V in a 48-TSSOP package.

The 74FCT162H245CTPVC from Cypress Semiconductor Corp is a non-inverting transceiver Integrated Circuit rated 5.5 V, in a 48-SSOP package.

The 74FCT162823CTPVG from IDT, Integrated Device Technology Inc is a dual D-type flip-flop with 2 elements, 9 bits per element and positive edge triggering, in a 56-BSSOP package (0.295", 7.50 mm width).

74FCT162543ATPACT from Texas Instruments is a Integrated Circuit 16-Bit Registered Transceivers with 3-State Outputs - General-purpose transceivers. The CY74FCT16543T and CY74FCT162543T are 16-bit, high-speed, low power latched transceivers that are organized as two independent 8-bit D-type latched transceivers containing two sets of eight D-type latches with separate Latch Enable (LEAB, LEAB) and Output Enable (OEAB, OEAB) controls for each set to permit independent control of inputting and outputting in either direction of data flow. For data flow from A to B, for example, the A-to-B input Enable (CEAB) must be LOW in order to enter data from A or to take data from B as indicated in the truth table. With CAEB LOW, a LOW signal on the A-to-B Latch Enable (LEAB) makes the A-to-B latches transparent; a subsequent LOW-to-HIGH transition of the LEAB signal puts the A latches in the storage mode and their outputs no longer change with the A inputs. With CEAB and OEAB both LOW, the three-state B output buffers are active and reflect the data present at the output of the A latches. Control of data from B to A is similar, but uses CEAB, LEAB, and OEAB inputs flow-through pinout and small shrink packaging and in simplifying board design. This device is fully specified for partial-power-down applications using I off. The I off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The CY74FCT16543T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162543T has 24-mA balanced output drivers with current limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce. The CY74FCT162543T is ideal for driving transmission lines. The CY74FCT162H543T is a 24-mA balanced output part that has "bus hold" on the data inputs. The device retains the inputx92s last state whenever the input goes to high impedance. This eliminates the need for pull-up/down resistors and prevents floating inputs.

The 74FCT162646ATPVCT from Texas Instruments is a non-inverting transceiver rated at 5.5 V, in a 56-SSOP package.

74FCT162543CTPACT from Texas Instruments is a Integrated Circuit 16-Bit Registered Transceivers with 3-State Outputs - General-purpose transceivers. The CY74FCT16543T and CY74FCT162543T are 16-bit, high-speed, low power latched transceivers that are organized as two independent 8-bit D-type latched transceivers containing two sets of eight D-type latches with separate Latch Enable (LEAB, LEAB) and Output Enable (OEAB, OEAB) controls for each set to permit independent control of inputting and outputting in either direction of data flow. For data flow from A to B, for example, the A-to-B input Enable (CEAB) must be LOW in order to enter data from A or to take data from B as indicated in the truth table. With CAEB LOW, a LOW signal on the A-to-B Latch Enable (LEAB) makes the A-to-B latches transparent; a subsequent LOW-to-HIGH transition of the LEAB signal puts the A latches in the storage mode and their outputs no longer change with the A inputs. With CEAB and OEAB both LOW, the three-state B output buffers are active and reflect the data present at the output of the A latches. Control of data from B to A is similar, but uses CEAB, LEAB, and OEAB inputs flow-through pinout and small shrink packaging and in simplifying board design. This device is fully specified for partial-power-down applications using I off. The I off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The CY74FCT16543T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162543T has 24-mA balanced output drivers with current limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce. The CY74FCT162543T is ideal for driving transmission lines. The CY74FCT162H543T is a 24-mA balanced output part that has "bus hold" on the data inputs. The device retains the inputx92s last state whenever the input goes to high impedance. This eliminates the need for pull-up/down resistors and prevents floating inputs.

The 74FCT16245ETPVG from IDT, Integrated Device Technology Inc is a non-inverting transceiver Integrated Circuit with 2 elements, 8 bits per element and 3-state outputs, rated 5.5 V, in a 48-SSOP package.

The 74FCT162374ETPAG from IDT, Integrated Device Technology Inc is a D-type flip flop Integrated Circuit with 2 elements, 8 bits per element and positive edge triggering, in a 48-TFSOP package (0.240", 6.10 mm width).

The 74FCT162501ATPVG from IDT, Integrated Device Technology Inc is an 18-bit registered universal bus transceiver in a 56-SSOP package.

The 74FCT162240CTPACT from Texas Instruments is an inverting buffer Integrated Circuit with 4 elements of 4 bits each and 3-state outputs, rated at 5.5 V, in a 48-TSSOP package.

The 74FCT162245CTPAG from IDT, Integrated Device Technology Inc is a non-inverting transceiver rated at 5.5 V in a 48-TSSOP package.

74FCT162827ATPACT from Texas Instruments is a Integrated Circuit 20-ch, 4.5-V to 5.5-V buffers with TTL-compatible CMOS inputs and 3-state outputs - Noninverting buffers & drivers. The CY74FCT16827T 20-bit buffer/line driver and the CY74FCT162827T 20-bit buffer/line driver provide high-performance bus interface buffering for wide data/address paths or buses carrying parity. These parts can be used as a single 20-bit buffer or two 10-bit buffers. Each 10-bit buffer has a pair of NANDed OE for increased flexibility. This device is fully specified for partial-power-down applications using I off. The I off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The CY74FCT16827T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162827T has 24-mA balanced output drivers with current-limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce. The CY74FCT162827T is ideal for driving transmission lines.

The 74FCT16245ATPVG from IDT, Integrated Device Technology Inc is a non-inverting transceiver Integrated Circuit with 2 elements, 8 bits per element and 3-state outputs, rated 5.5 V, in a 48-SSOP package.

The 74FCT16245CTPVG8 from IDT, Integrated Device Technology Inc is a non-inverting transceiver with 2 elements of 8 bits each and 3-state outputs, rated 5.5 V, in a 48-SSOP package.

The 74FCT162244CTPACT from Texas Instruments is a non-inverting buffer Integrated Circuit rated to 5.5 V, with 4 elements of 4 bits each, 3-state outputs and a 48-TSSOP package.

The 74FCT162823CTPAG from IDT, Integrated Device Technology Inc is a dual D-type flip-flop with 2 elements, 9 bits per element and positive edge triggering, in a 56-TFSOP package (0.240", 6.10 mm width).

The 74FCT162244LBCTPV from IDT, Integrated Device Technology Inc is a 16-bit fast CMOS buffer/line driver Integrated Circuit.

The 74FCT162244ATPVC from Texas Instruments is a non-inverting buffer Integrated Circuit with 4 elements, 4 bits per element and 3-state output, rated 5.5 V, in a 48-SSOP package.

The 74FCT162374ETPACT from Cypress Semiconductor Corp is an FCT-series bus driver Integrated Circuit.

74FCT162646CTPACT from Texas Instruments is a Integrated Circuit 16-Bit Bus Transceivers and Registers with 3-State Outputs - General-purpose transceivers. The CY74FCT16646T and CY74FCT162646T 16-bit transceivers are three-state, D-type registers, and control circuitry arranged for multiplexed transmission of data directly from the input bus or from the internal registers. Data on the A or B bus will be clocked into the registers as the appropriate clock pin goes to a HIGH logic level. Output Enable (OE) and direction pins (DIR) are provided to control the transceiver function. In the transceiver mode, data present at the high impedance port may be stored in either the A or B register, or in both. The select controls can multiplex stored and real-time (transparent mode) data. The direction control determines which bus will receive data when the Output Enable (OE) is Active LOW. In the isolation mode (Output Enable (OE) HIGH), A data may be stored in the B register and/or B data may be stored in the A register. This device is fully specified for partial-power-down applications using I off. The I off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The CY74FCT16646T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162646T has 24-mA balanced output drivers with current limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce. The CY74FCT162646T is ideal for driving transmission lines.

The 74FCT162245ATPVCT from Cypress Semiconductor Corp is a non-inverting transceiver with 2 elements of 8 bits each and 3-state outputs, rated 5.5 V, in a 48-SSOP package.

The 74FCT162373ATPVCT from Cypress Semiconductor Corp is a 16-bit transparent latch Integrated Circuit with a channel specification.

The 74FCT162500ATPVG from IDT, Integrated Device Technology Inc is a non-inverting universal bus transceiver rated to 5.5 V, in a 56-SSOP package.