Search results for “MultiMaster™”

The MTCDT-STARTER KIT-868 from Multi-Tech Systems Inc. is a Multiconnect Conduit LoRa starter kit at 868 MHz with Bluetooth, GNSS, LTE and WLAN, plus Ethernet and USB.

The MTCDT-STARTER KIT-915 from Multi-Tech Systems Inc. is a MultiConnect Conduit LoRa starter kit for 915 MHz.

S5LS20206ASGWTMEP from Texas Instruments is a Integrated Circuit Enhanced Product 16- and 32-Bit RISC Flash Microcontroller - Real-time motor control & automation MCUs. The TMS570LS series is a high performance microcontroller family. The architecture includes Dual CPUs in lockstep, CPU and Memory Built-In Self Test (BIST) logic, ECC on both the Flash and the data SRAM, parity on peripheral memories, and loop back capability on peripheral IOs. The TMS570LS family integrates the ARM® Cortex™-R4F Floating Point CPU which offers an efficient 1.6 DMIPS/MHz, and has configurations which can run up to 160 MHz providing more than 250 DMIPS. The TMS570LS series also provides Flash (2MB) and data SRAM (160KB) options with single bit error correction and double bit error detection. The TMS570LS devices feature peripherals for real-time control-based applications, including up to 32 nHET timer channels and two 12-bit A to D converters supporting up to 24 inputs. There are multiple communication interfaces including a 2-channel FlexRay, 3 CAN controllers supporting 64 mailboxes each, and 2 LIN/UART controllers. With a wide choice of communication and control peripherals, the TMS570LS series is an ideal solution for high performance real time control applications. The devices included in the TMS570LS series and described in this document are: TMS570LS20206 TMS570LS20216 The TMS570LS series microcontrollers contain the following: Dual TMS570 16/32-Bit RISC (ARM Cortex™-R4F) in Lockstep Up to 2M-Byte Program Flash with ECC Up to 160K-Byte Static RAM (SRAM) with ECC Real-Time Interrupt (RTI) Operating System Timer Vectored Interrupt Module (VIM) Cyclic Redundancy Checker (CRC) with Parallel Signature Analysis (PSA) Direct Memory Access (DMA)Controller Frequency-Modulated Phase-Locked Loop (FMzPLL)-Based Clock Module With Prescaler Three Multi-buffered Serial Peripheral Interfaces (MibSPI) Two UARTs (SCI) with Local Interconnect Network Interfaces (LIN) Three CAN Controllers (DCAN) High-End Timer (NHET) with dedicated Transfer Unit (HTU) Available FlexRay Controller with dedicated PLL and Transfer Unit (FTU) External Clock Prescale (ECP) Module Two 16-Channel 12-Bit Multi-Buffered ADCs (MibADC) - 8 shared channels between the two ADCs Address Bus Parity with Failure Detection Error Signaling Module (ESM) with external error pin Voltage Monitor (VMON) with out of range reset assertion Embedded Trace Module (ETMR4) Data Modification Module (DMM) RAM Trace Port (RTP) Parameter Overlay Module (POM) 16 Dedicated General-Purpose I/O (GIO) Pins for GWT; 8 Dedicated GIO Pins for PGE 115 Total Peripheral I/Os for GWT; 68 Total Peripheral I/Os for PGE 16-Bit External Memory Interface (EMIF) The devices utilize the big-endian format where the most significant byte of a word is stored at the lowest numbered byte and the least significant byte at the highest numbered byte. The device memory includes general-purpose SRAM supporting single-cycle read/write accesses in byte, halfword, and word modes. The flash memory on this device is a nonvolatile, electrically erasable and programmable memory implemented with a 64-bit-wide data bus interface. The flash operates on a 3.3V supply input (same level as I/O supply) for all read, program and erase operations. When in pipeline mode, the flash operates with a system clock frequency of up to 160 MHz. The device has nine communication interfaces: three MibSPIs, two LIN/SCIs, three DCANs and one FlexRay™ controller (optional). The SPI provides a convenient method of serial interaction for high-speed communications between similar shift-register type devices. The LIN supports the Local Interconnect standard 2.0 and can be used as a UART in full-duplex mode using the standard Non-Return-to-Zero (NRZ) format. The DCAN supports the CAN 2.0B protocol standard and uses a serial, multimaster communication protocol that efficiently supports distributed real-time control with robust communication rates of up to 1 megabit per second (Mbps). The DCAN is ideal for applications operating in noisy and harsh environments that require reliable serial communication or multiplexed wiring. The FlexRay uses a dual channel serial, fixed time base multimaster communication protocol with communication rates of 10 megabits per second (Mbps) per channel. A FlexRay Transfer Unit (FTU) enables autonomous transfers of FlexRay data to and from main CPU memory. Transfers are protected by a dedicated, built-in Memory Protection Unit (MPU). The NHET is an advanced intelligent timer that provides sophisticated timing functions for real-time applications. The timer is software-controlled, using a reduced instruction set, with a specialized timer micromachine and an attached I/O port. The NHET can be used for pulse width modulated outputs, capture or compare inputs, or general-purpose I/O. It is especially well suited for applications requiring multiple sensor information and drive actuators with complex and accurate time pulses. A High End Timer Transfer Unit (HET-TU) provides features to transfer NHET data to or from main memory. A Memory Protection Unit (MPU) is built into the HET-TU to protect against erroneous transfers. The device has two 12-bit-resolution MibADCs with 24 total channels and 64 words of parity protected buffer RAM each. The MibADC channels can be converted individually or can be grouped by software for sequential conversion sequences. Eight channels are shared between the two ADCs. There are three separate groupings, two of which are triggerable by an external event. Each sequence can be converted once when triggered or configured for continuous conversion mode. The frequency-modulated phase-locked loop (FMzPLL) clock module contains a phase-locked loop, a clock-monitor circuit, a clock-enable circuit, and a prescaler. The function of the FMzPLL is to multiply the external frequency reference to a higher frequency for internal use. The FMzPLL provides one of the six possible clock source inputs to the global clock module (GCM). The GCM module provides system clock (HCLK), real-time interrupt clock (RTICLK1), CPU clock (GCLK), NHET clock (VCLK2), DCAN clock (AVCLK1), and peripheral interface clock (VCLK) to all other peripheral modules. The device also has an external clock prescaler (ECP) module that when enabled, outputs a continuous external clock on the ECLK pin. The ECLK frequency is a user-programmable ratio of the peripheral interface clock (VCLK) frequency. The Direct Memory Access Controller (DMA) has 32 DMA requests, 16 Channels/ Control Packets and parity protection on its memory. The DMA provides memory to memory transfer capabilities without CPU interaction. A Memory Protection Unit (MPU) is built into the DMA to protect memory against erroneous transfers. The Error Signaling Module (ESM) monitors all device errors and determines whether an interrupt or external Error pin is triggered when a fault is detected. The External Memory Interface (EMIF) provides a memory extension to asynchronous memories or other slave devices. Several interfaces are implemented to enhance the debugging capabilities of application code. In addition to the built in ARM Cortex™-R4F CoreSight™ debug features, an External Trace Macrocell (ETM) provides instruction and data trace of program execution. For instrumentation purposes, a RAM Trace Port Module (RTP) is implemented to support high-speed output of RAM accesses by the CPU or any other master. A Direct Memory Module (DMM) gives the ability to write external data into the device memory. Both the RTP and DMM have no or only minimum impact on the program execution time of the application code. A Parameter Overlay Module (POM) can re-route Flash accesses to the EMIF, thus avoiding the re-programming steps necessary for parameter updates in Flash.

S5LS20216ASGWTMEP from Texas Instruments is a Integrated Circuit Enhanced Product 16- and 32-Bit RISC Flash Microcontroller - Real-time motor control & automation MCUs. The TMS570LS series is a high performance microcontroller family. The architecture includes Dual CPUs in lockstep, CPU and Memory Built-In Self Test (BIST) logic, ECC on both the Flash and the data SRAM, parity on peripheral memories, and loop back capability on peripheral IOs. The TMS570LS family integrates the ARM® Cortex™-R4F Floating Point CPU which offers an efficient 1.6 DMIPS/MHz, and has configurations which can run up to 160 MHz providing more than 250 DMIPS. The TMS570LS series also provides Flash (2MB) and data SRAM (160KB) options with single bit error correction and double bit error detection. The TMS570LS devices feature peripherals for real-time control-based applications, including up to 32 nHET timer channels and two 12-bit A to D converters supporting up to 24 inputs. There are multiple communication interfaces including a 2-channel FlexRay, 3 CAN controllers supporting 64 mailboxes each, and 2 LIN/UART controllers. With a wide choice of communication and control peripherals, the TMS570LS series is an ideal solution for high performance real time control applications. The devices included in the TMS570LS series and described in this document are: TMS570LS20206 TMS570LS20216 The TMS570LS series microcontrollers contain the following: Dual TMS570 16/32-Bit RISC (ARM Cortex™-R4F) in Lockstep Up to 2M-Byte Program Flash with ECC Up to 160K-Byte Static RAM (SRAM) with ECC Real-Time Interrupt (RTI) Operating System Timer Vectored Interrupt Module (VIM) Cyclic Redundancy Checker (CRC) with Parallel Signature Analysis (PSA) Direct Memory Access (DMA)Controller Frequency-Modulated Phase-Locked Loop (FMzPLL)-Based Clock Module With Prescaler Three Multi-buffered Serial Peripheral Interfaces (MibSPI) Two UARTs (SCI) with Local Interconnect Network Interfaces (LIN) Three CAN Controllers (DCAN) High-End Timer (NHET) with dedicated Transfer Unit (HTU) Available FlexRay Controller with dedicated PLL and Transfer Unit (FTU) External Clock Prescale (ECP) Module Two 16-Channel 12-Bit Multi-Buffered ADCs (MibADC) - 8 shared channels between the two ADCs Address Bus Parity with Failure Detection Error Signaling Module (ESM) with external error pin Voltage Monitor (VMON) with out of range reset assertion Embedded Trace Module (ETMR4) Data Modification Module (DMM) RAM Trace Port (RTP) Parameter Overlay Module (POM) 16 Dedicated General-Purpose I/O (GIO) Pins for GWT; 8 Dedicated GIO Pins for PGE 115 Total Peripheral I/Os for GWT; 68 Total Peripheral I/Os for PGE 16-Bit External Memory Interface (EMIF) The devices utilize the big-endian format where the most significant byte of a word is stored at the lowest numbered byte and the least significant byte at the highest numbered byte. The device memory includes general-purpose SRAM supporting single-cycle read/write accesses in byte, halfword, and word modes. The flash memory on this device is a nonvolatile, electrically erasable and programmable memory implemented with a 64-bit-wide data bus interface. The flash operates on a 3.3V supply input (same level as I/O supply) for all read, program and erase operations. When in pipeline mode, the flash operates with a system clock frequency of up to 160 MHz. The device has nine communication interfaces: three MibSPIs, two LIN/SCIs, three DCANs and one FlexRay™ controller (optional). The SPI provides a convenient method of serial interaction for high-speed communications between similar shift-register type devices. The LIN supports the Local Interconnect standard 2.0 and can be used as a UART in full-duplex mode using the standard Non-Return-to-Zero (NRZ) format. The DCAN supports the CAN 2.0B protocol standard and uses a serial, multimaster communication protocol that efficiently supports distributed real-time control with robust communication rates of up to 1 megabit per second (Mbps). The DCAN is ideal for applications operating in noisy and harsh environments that require reliable serial communication or multiplexed wiring. The FlexRay uses a dual channel serial, fixed time base multimaster communication protocol with communication rates of 10 megabits per second (Mbps) per channel. A FlexRay Transfer Unit (FTU) enables autonomous transfers of FlexRay data to and from main CPU memory. Transfers are protected by a dedicated, built-in Memory Protection Unit (MPU). The NHET is an advanced intelligent timer that provides sophisticated timing functions for real-time applications. The timer is software-controlled, using a reduced instruction set, with a specialized timer micromachine and an attached I/O port. The NHET can be used for pulse width modulated outputs, capture or compare inputs, or general-purpose I/O. It is especially well suited for applications requiring multiple sensor information and drive actuators with complex and accurate time pulses. A High End Timer Transfer Unit (HET-TU) provides features to transfer NHET data to or from main memory. A Memory Protection Unit (MPU) is built into the HET-TU to protect against erroneous transfers. The device has two 12-bit-resolution MibADCs with 24 total channels and 64 words of parity protected buffer RAM each. The MibADC channels can be converted individually or can be grouped by software for sequential conversion sequences. Eight channels are shared between the two ADCs. There are three separate groupings, two of which are triggerable by an external event. Each sequence can be converted once when triggered or configured for continuous conversion mode. The frequency-modulated phase-locked loop (FMzPLL) clock module contains a phase-locked loop, a clock-monitor circuit, a clock-enable circuit, and a prescaler. The function of the FMzPLL is to multiply the external frequency reference to a higher frequency for internal use. The FMzPLL provides one of the six possible clock source inputs to the global clock module (GCM). The GCM module provides system clock (HCLK), real-time interrupt clock (RTICLK1), CPU clock (GCLK), NHET clock (VCLK2), DCAN clock (AVCLK1), and peripheral interface clock (VCLK) to all other peripheral modules. The device also has an external clock prescaler (ECP) module that when enabled, outputs a continuous external clock on the ECLK pin. The ECLK frequency is a user-programmable ratio of the peripheral interface clock (VCLK) frequency. The Direct Memory Access Controller (DMA) has 32 DMA requests, 16 Channels/ Control Packets and parity protection on its memory. The DMA provides memory to memory transfer capabilities without CPU interaction. A Memory Protection Unit (MPU) is built into the DMA to protect memory against erroneous transfers. The Error Signaling Module (ESM) monitors all device errors and determines whether an interrupt or external Error pin is triggered when a fault is detected. The External Memory Interface (EMIF) provides a memory extension to asynchronous memories or other slave devices. Several interfaces are implemented to enhance the debugging capabilities of application code. In addition to the built in ARM Cortex™-R4F CoreSight™ debug features, an External Trace Macrocell (ETM) provides instruction and data trace of program execution. For instrumentation purposes, a RAM Trace Port Module (RTP) is implemented to support high-speed output of RAM accesses by the CPU or any other master. A Direct Memory Module (DMM) gives the ability to write external data into the device memory. Both the RTP and DMM have no or only minimum impact on the program execution time of the application code. A Parameter Overlay Module (POM) can re-route Flash accesses to the EMIF, thus avoiding the re-programming steps necessary for parameter updates in Flash.

The X9260TS24 from Renesas Electronics America Inc is a digital potentiometer with 100 kΩ resistance, 2 circuits, 256 taps and an SPI interface, in a 24-SOIC package.

The MOC5009FVM from onsemi is a logic-output optoisolator with a 1 MHz open-collector output and 1 channel, rated 7500 Vpk with CMTI, in a 6-SMD package.

The 11543 from Master Appliance Co is a red, inline solder butt splice for 18-20 AWG wire, sold in packs of 100.

The X9259TS24-2.7 from Renesas Electronics America Inc is a digital potentiometer with 100 kΩ resistance, 4 circuits, 256 taps and an I²C interface, in a 24-SOIC package.

The QB-FN1-Q from Panduit Corp is a nail holder for the Quick-Build harness board system, supplied in a multi-pack of 5 (1 = 25).

The T050X000VPM-BK from Panduit Corp is a white standard continuous label for MP cassette printers, 0.47" x 276.00" (12.0 mm x 7010.4 mm).

The SI5338C-B04404-GMR from Skyworks Solutions Inc. is an I2C-controlled 4-output clock Integrated Circuit for any frequency, in a 24-QFN (4x4) package.

The SI5338Q-A-GM from Skyworks Solutions Inc. is a programmable clock generator Integrated Circuit with an I2C bus for Ethernet, Fibre Channel, PCI Express (PCIe) and telecom applications, offering 200 MHz and 1 output in a 24-QFN (4x4) package.

The PCM-6 from Panduit Corp is a wire marker card measuring 0.25" W x 1.50" L (6.4 mm x 38.1 mm), made of white vinyl cloth.

The DAPI-MULTI from Panduit Corp is a universal international socket.

The RMAS8 from Switchcraft Inc. is an 8-channel audio splitter.

The MASTERGAN3TR from STMicroelectronics is a half-bridge driver Integrated Circuit rated 6.5 A/4 A in a 31-QFN package.

The MASTERGAN4 from STMicroelectronics is a general-purpose half-bridge driver Integrated Circuit rated at 6.5 A, in a 31-QFN (9x9) package.

The MASTERGAN5 from STMicroelectronics is a 4 A half-bridge driver for DC-DC converters, in a 31-QFN (9x9) package.

The 227-T2000 from Amphenol RF is an insertion and extraction tool for HD-BNC coaxial Radio Frequency connectors.

The PCM-10 from Panduit Corp is a wire marker card measuring 0.25" W x 1.50" L (6.4 mm x 38.1 mm), made of white vinyl cloth.

The SI5338C-B05394-GM from Skyworks Solutions Inc. is an I2C-controlled, 4-output clock Integrated Circuit with any frequency, in a 24-QFN (4x4) package.

The T075X000VPM-BK from Panduit Corp is a white standard continuous label for MP cassette printers, 0.71" x 276.00" (18.0 mm x 7010.4 mm).

The 11840 from Master Appliance Co is a clear, inline solder butt splice for 22-24 AWG wire, supplied in packs of 50.

The CT10 from Psiber Data Systems, Inc. is a network testing tone generator for cable tracing.

The R5F3640DDFB#V2 from Renesas Electronics America Inc is a 16-bit microcontroller with 256 KB flash memory, in a 100-LQFP package.

The EMZA100ARA330MD61G from United Chemi-Con is a 33 µF ±20% 10 V aluminum electrolytic capacitor in an SMD can, rated 2000 hours at 105 °C.

The M306N4MGT-165FPUSQ from Renesas Electronics America Inc is a 16-bit microcontroller Integrated Circuit from the M16C/60 (M16C/60/6N4) series running at 20 MHz, with 256 KB (256K x 8) mask ROM in a 100-QFP (14x20) package.

The T150X000VPM-BK from Panduit Corp is a white standard continuous label tape cassette measuring 1.47" x 276.00" (37.4 mm x 7010.4 mm).

The PCM-1 from Panduit Corp is a wire marker card measuring 0.25" W x 1.50" L (6.4 mm x 38.1 mm), made of white vinyl cloth.

The 48540 from Littelfuse Inc. is a smart isolator controller, dual V.

The X9260US24Z from Renesas Electronics America Inc is a digital potentiometer with 50 kΩ resistance, 2 circuits, 256 taps and an SPI interface, in a 24-SOIC package.

The HSCM-2400-0.390-WT from Brady Corporation is a white polyurethane (PUR) cable tie wire marker measuring 2.40" W x 0.40" L (61.0 mm x 10.2 mm).

The TMP60 from Triplett Test Equipment and Tools is a dual-input Type K/J thermometer.

The SI5338A-B02454-GMR from Skyworks Solutions Inc. is an I2C-controlled 4-output Integrated Circuit with any-frequency output, in a 24-QFN (4x4) package.

The T100X000VPM-BK from Panduit Corp is a white standard continuous label tape cassette measuring 0.95" x 276.00" (24.0 mm x 7010.4 mm).

The HSCM-3000-0.625-YL from Brady Corporation is a yellow polyurethane (PUR) cable tie wire marker measuring 3.00" W x 0.63" L (76.2 mm x 15.9 mm).